Design and implementation of smart integrated hybrid Solar-Darrieus wind turbine system for in-house power generation

. This paper presents the design and development of an integrated hybrid Solar-Darrieus wind turbine system for renewable power generation. The Darrieus wind turbine ’ s performance is meticulously assessed using the SG6043 airfoil, determined through Q-blade simulation, and validated via comprehensive CFD simulations. The study identi ﬁ es SG6043 as the optimal airfoil, surpassing alternatives. CFD simulations yield speci ﬁ c coef ﬁ cients of power (0.2366) and moment (0.0288). The paper also introduces a hybrid prototype, showcasing of 10 W photovoltaic module and improved turbine performance with the SG6043 airfoil. The focus extends to an optimized hybrid PV solar-wind system seamlessly integrated with IoT technology for remote monitoring. Addressing weather challenges, the research suggests blade shape optimizations via Q-blade and an IoT-based solution leveraging the ESP32 Wi-Fi module. Theoretical results project electrical energy generation ranging from 0.88 kW on March 14, 2023, to 0.06 kW on February 20, 2023. Darrieus wind turbines, experiencing increased blade drag, require less lift to operate. Experimental and theoretical results converge well, af ﬁ rming the model ’ s reasonable assumptions. Beyond advancing renewable energy technologies, this research sets the stage for future investigations aimed at enhancing the ef ﬁ ciency and capabilities of hybrid wind-solar PV systems.


Introduction
The increasing global focus on energy demand has driven movements towards carbon neutrality and the adoption of renewable energy sources.Conventional energy sources, though historically relied upon for their high energy density, raise environmental concerns due to carbon and greenhouse gas emissions.As projected energy demand is set to rise by 56% from 2010 to 2040, the significance of renewable energy power plants has grown [1].Malaysia has witnessed notable growth in photovoltaic (PV) systems, leveraging its hot and humid climate to harness substantial solar radiation [2].Wind energy utilization in Malaysia has gained attention in recent years as the country seeks to diversify its energy mix and reduce its dependence on fossil fuels.While Malaysia has traditionally focused on hydroelectric and fossil fuel-based energy sources, wind energy is gradually being explored and integrated into its power generation landscape [3].The Darrieus wind turbine is a type of "vertical-axis wind turbine" (VAWT) known for its distinctive helical or "eggbeater" shape.Unlike traditional "horizontal-axis wind turbines" (HAWTs), which have their blades oriented parallel to the ground, Darrieus turbines have blades that rotate around a vertical axis, perpendicular to the ground.This unique design of the blades offers several advantages and challenges in harnessing wind energy such as [4,5]: (i) the vertical plane, allowing them to capture wind from any direction without needing to constantly rotate to face the wind, (ii) an aerodynamic airfoil shape and are arranged in a helical pattern around the central vertical axis.This design enables self-starting capabilities and helps in capturing wind energy from various wind speeds and directions, (iii) the blades are tall compared to their width, allowing them to capture higher altitude wind currents effectively, (iv) used in smaller-scale applications, such as residential or community-based installations.The motivation behind designing a solar-darius hybrid wind turbine system for indoor power generation stems from the urgent need to address the challenges posed by conventional energy sources and their associated environmental impacts.Working with a hybrid solar-wind system may be a promising solution because it harnesses the complementary nature of solar and wind energy to ensure stable and sustainable energy generation.These hybrid systems will be suitable for residential and small-scale applications.It must be taken into consideration that the wind energy industry faces many challenges, including: low wind speeds and variability, which makes continuous and stable electricity generation using wind energy something that cannot be achieved in natural conditions.However, studies point to potential solutions to increase the viability of wind energy through turbine design analysis.To address these concerns and improve renewable energy systems, a hybrid approach that combines wind and solar power has emerged [6].Solar energy has several characteristics that make it suitable for generating energy.It is a renewable resource, meaning it is constantly renewed by the sun.As long as the sun exists, we can harness its energy to generate energy.It is also an abundant energy source as it radiates a huge amount of energy every day, much more than humanity currently consumes.This makes solar energy an almost limitless resource [7].Also, solar energy is clean and environmentally friendly: generating solar energy does not produce any greenhouse gas emissions or air pollutants.It is a clean and environmentally friendly energy source.Solar energy systems provide energy independence to homeowners, businesses, and even entire regions.They reduce dependence on fossil fuels and centralized energy grids [8].Considering the crucial role of energy in economic development, welfare, and overall quality of life, exploring renewable energy alternatives becomes imperative [9].Wind and solar energy sources offer clean options, and a hybrid system combining both ensures continuous power output.However, weather variations pose challenges to both standalone renewable sources and hybrid systems, affecting their stability and voltage production [10].The current study aims to improve voltage production and overall system stability by optimizing the blade shape.Using the Darius wind turbine as a case study, this paper will analyze the operating mechanism, factors that affect its performance, and its self-starting abilities to improve the solar-wind hybrid power generation system in Malaysia.Models of the relevant equations are derived using Computational Fluid Dynamics (CFD) and Q-blade to simulate turbines.A hybrid solar-wind power generator with enhanced power production capabilities and selfstarting ability is the ultimate goal.There is also a discussion of the experimental design and validation.Based on the researcher's knowledge, no previous studies have addressed this new design trend.

Literature review
The working principal of a Darrieus VAWT was noted as a wind turbine that uses the lift force generated to create the movement and power generation in contrast to the Savonius VAWT which uses the drag force generated from the wind.Darrieus wind turbines commonly have two or three blades and are alternatively known as "eggbeaters" due to its C-shaped rotor blades creating the shape of an eggbeater.However, this design was the turbine that was patented in 1931, where the evolution and innovation of the technology has brought upon various designs such as the H-Darrieus and the helical Darrieus.The turbine has good efficiency but low reliability from the large torque ripple and cyclic stress produced on the tower [11].
A commonly known fact from the research found is that the Darrieus turbine requires an exterior power source to assist in the initiation of rotation of the turbine because of its low starting torque.Therefore, among the studies conducted, the research on the self-starting ability of the turbine has been conducted to tackle this limitation of this turbine.A parameter that is frequently discussed on the self-starting of the system is the "tip speed ratio" (TSR) which is described as the relation between the wind speed and the speed of the tips of the turbine.This parameter plays a major role in the efficiency of the turbine.Another important parameter considered in the design of the blades is the angle of attack, a, which represents the angle between the body's reference line and the oncoming flow.This angle affects the lift and drag experienced on the turbine which indefinitely affects the performance of the wind turbine.However, it was also found that the low TSRs are not suitable for the operation of the turbine as flow separation destabilizes the rotation of the blade.It was also determined that there is still potential for the advancement of the wind turbine through rotor arrangements and wind farms computational analysis [12,13].
Aside from self-starting ability, efficiency and optimization of the wind turbine were discussed in the studies, with CFD analysis used in the majority of cases.An unsteady (transient) ''Reynolds-Averaged-Navier-Stokes'' (URANS) method was used as well as a quadratic equation based on a regression model and a rotational degree of freedom solver (6DOF).Obtaining an accurate prediction of the turbine's behavior during startup requires the correct distribution of the lift and drag forces [14,15].
In Malaysia, the design of the hybrid energy system is more distinct and clear when dealing with wind energy due to the low average annual speed that the country experiences.A hybrid solar-wind power generator used to power street lighting has been designed and developed [16].In such designs, the engineering of solar panels is taken into account, as well as the optimization of wind turbines and their systems, with the aim of producing the maximum amount of energy possible.The question that always arises in such studies is the effect of deflected flow because it reduces the power output capacity of the power generator [17].
A hybrid power generation system has the potential to address the challenge of low mean annual wind speeds in Malaysia.Notably, research has been undertaken to optimize such a hybrid power generation system.In a related context, a study in Zimbabwe conducted optimization efforts for a hybrid power generation system that powered a streetlight using both solar and wind sources [18].This hybrid renewable energy system design encom- Additional research, such as the investigation into a Savonius-Darrieus hybrid system, can also contribute valuable insights to the advancement of hybrid systems.An illustrative case in point is a study conducted by [19].This study delved into the impact of the number of blades on a VAWT through computational analysis.The findings of this study revealed that a configuration comprising a two-bladed Savonius rotor and a three-bladed Darrieus rotor exhibited enhanced self-starting capabilities.Specifically, the values of 0.41 for the "maximum coefficient of power" (Cp) and 2.5 for the TSR were attained.This configuration not only demonstrated improved self-starting attributes but also showcased heightened efficiency.Furthermore, upon comparing the proposed design configuration with previously devised hybrid VAWTs, the study demonstrated an augmentation in self-starting proficiency and overall efficiency.This serves to emphasize the potential benefits of optimizing blade numbers within a hybrid system, contributing to the on-going evolution of renewable energy technologies.
The objective of a study conducted by [20] was to delve into the intricate physics involved during the self-starting phase of a specific system.This was achieved through a two-dimensional CFD approach.In this context, the situational simulation employed ANSYS Fluent software, where the mesh generation utilized the sliding technique, and the "Six Degrees of Freedom" (6DOF) rotational degree was enabled.The results of this research provide valuable insights into the correlation between the local absolute velocity of the blades and the instantaneous TSR during the initial and early revolutions of the motor.A noteworthy finding was that the LineAverage_1.25ctechnique proves to be more precise when compared to the 1-Points Average method for extracting flow dynamics around the blade.This is particularly pertinent in scenarios where flow separation and the formation of significant regions of eddies occur.Furthermore, the research delved into the behavior of dynamic stall and established the connection between the predicted angle of attack and the coefficients of lift and drag.These findings collectively contribute to an enhanced understanding of the self-starting phase's mechanics and the aerodynamic behavior of the system under scrutiny.
For the purpose of juxtaposing studies in the existing literature, Table 1 serves as an illustrative benchmark, delineating key facets for comparison.These facets encompass: F1-Working Mechanism of Darrieus Wind Turbine and/or Solar System: This factor delves into the operational intricacies of the Darrieus wind turbine and solar energy system, dissecting their functional synergies.
F2-Optimization Technology for Darrieus Rotor Blades: Within this parameter, the technological approaches employed for optimizing the performance of Darrieus rotor blades are examined.
F3-Geometry of Solar Panel: The geometry, configuration, and design specifics of the solar panel are appraised under this criterion.
F4-Development of Proposed Design: This factor scrutinizes the evolution and formulation of the proposed design within the context of the studied systems.By dissecting these facets and presenting their nuances within Table 1, a comprehensive comparison across various studies is facilitated, contributing to a more holistic comprehension of the research landscape.

Methodology and materials
The research method is initiated with the design of the Darrieus wind turbine rotor airfoil as the airfoil affects the self-starting capability of the rotor and its ability to generate power.In this phase, there are several parameters that must be considered such as the TSR, geometry of the rotor, drag and lift coefficient, solidity, and forces of drag and lift.
The Tip-Speed Ratio (TSR) is the ratio of the tangential speed of the tip of a wind turbine blade to the speed of the wind.If a wind turbine has a TSR of 5, it means the tip of the blade is moving five times faster than the wind speed.
The Geometry of the Rotor refers to the physical dimensions and characteristics of the wind turbine rotor, including the length and shape of the blades.A rotor with longer blades will capture more wind energy, while the shape of the blades influences aerodynamic performance.
The Drag Coefficient represents the drag force experienced by an object moving through a fluid, in this case, the wind.A low drag coefficient indicates that the rotor blades encounter less resistance, improving overall efficiency.
The Lift Coefficient measures the lift force generated by the wind turbine blades due to aerodynamic lift.A higher lift coefficient signifies increased lift force, contributing to the efficient rotation of the wind turbine.
Solidity is the ratio of the total blade area to the swept area of the rotor and provides insight into how much space the blades occupy in the rotor plane.A low solidity indicates more space between blades, potentially reducing interference and improving efficiency.
Forces of Drag and Lift represent the aerodynamic forces acting on the wind turbine blades, influencing their motion.Understanding the forces of drag and lift is crucial for optimizing blade design and overall performance in capturing wind energy.
The proposed system is then simulated with using Qblade to understand the overall performance of the system.The airfoil of the turbine will also be simulated using the software.Further analysis will be conducted using CFD to compare the results to the results obtained from Q-blade simulations, in addition to the other parameters that is obtained from CFD analysis.Figure 1 shows the isometric view of the hybrid power generator consisting of all the previously mentioned components.The battery is placed at the bottom for the stability of the hybrid power generator while also optimizing the geometrical placements of the components.
Table 2 displays the finalized geometry of the wind turbine rotor blade.The rotor is designed to have an overall diameter of 0.4 m and a rotor height of 0.3239 m.One turbine is to be used in the system.The rotor is equipped with three blades with the optimal LS (1)-0413 airfoil obtained from the optimization of the airfoil.
Figure 2a displays the view of overall view of four airfoils designed using Q-blade to propose the optimal design to be used in the hybrid solar-wind power generator.As previously mentioned, LS (1)-0413 is one of the airfoils that are being compared to other airfoils.NACA 0015 and NACA 0021 have been used as airfoils to be compared due to them being known as the conventional airfoils used.SG6046 has been determined as one of the airfoils of comparison due to the research by [32] that suggests the airfoil is the most effective airfoil for wind with low Reynolds number and used in a small VAWT.The research found that SG6043 obtained the largest lift to drag ratio of the airfoils compared airfoil if NACA0018, NACA0021, and LS (1)-0413.2b illustrates the geometry to be simulated and the boundary conditions are determined to then be sent to the mesh generator.The geometry of the 2D airfoils has been drawn in ANSYS Fluent in the shape of the rotor turbine with diameter of 0.4 m where the surfaces of the airfoils act as walls.

System components
The material selection for a hybrid solar-wind system involves considering various factors such as durability, efficiency, cost-effectiveness, and sustainability.In Malaysia, being an equatorial country, the daily average solar radiation ranges approximately from 4,000 to 5,000 Wh/m 2 , with an annual average of 1,643 kWh/m 2 of received radiation.The proposed system design is illustrated in Figure 3.A summary of the materials selected for different components of the system: Figure 3b illustrates the designed system materials.

Integration strategy
The methodology encompasses the design specifications and process for the IoT system as shown in Figure 4a.It begins with a detailed discussion of IoT principles, emphasizing the significance of understanding its functionalities for software integration.A critical aspect addressed is the proposed monitoring system design, crucial for data management and analysis, facilitating issue identification, device optimization, and system efficiency.The IoT architecture is presented, comprising four layers: application, cloud management, network, and device.The application layer collects user data and offers smart services, while the cloud management layer centrally controls and analyses data.The network layer facilitates device connectivity, and the device layer collects data from sensing equipment and smart devices, transmitting it to the cloud.
The transmission hardware design, illustrated in Figure 4b, involves a wireless sensor network, server cloud management, and a workstation.Sensors collect data and transmit it through a Wi-Fi module, connecting with the cloud server that processes and stores the information.The workstation serves as the central control centre accessible via remote login.
The proposed approach's process flow is depicted in Figure 5a, illustrating sequential operations.The system starts with Arduino establishing an internet connection, generating an IP address.Valuable data from the hybrid system and sensors is processed by the microcontroller and efficiently transferred to the Blynk cloud server, accessible to authorized users.
The circuit design in Figure 5b incorporates two sensors controlled by the microcontroller to read data and energy from the hybrid system.The microcontroller is powered by a 5V-12V adapter, and a relay module allows remote and automatic control of the hybrid system on/off switch.The system's codes are developed in the Arduino IDE software for seamless data transfer.

Performance evaluation
The performance of the system is assessed and compared against meticulously calibrated sensor data.Calibration is conducted for the voltage and temperature sensors using a multi-meter and a thermometer, respectively, to ensure precise readings.To determine the variation between the actual and theoretical values, the percentage difference will be computed based on the calibration results obtained from the sensors.The Mean Formula will be employed to calculate the average data value, while the Standard Deviation Formula will be utilized for assessing standard deviation.It is important to note that standard deviation serves as a measure of uncertainty, representing the accuracy of the data.
The following formulas are employed for the calculations [2]: Mean Formula Standard Deviation Formula

System design and analysis
This section addresses material selection and cost analysis for key components of the hybrid system, encompassing the solar module, wind turbine design, IoT cloud infrastructure, IoT programming, and software integration.This integration facilitates remote monitoring through the Blynk web and app platform, employing the NodeMCU Wi-Fi module to interface with temperature and humidity sensors, voltage sensing, and a relay module to regulate This segment outlines the process of wind turbine blade design and simulation utilizing the blade element momentum theory (BEMT) through Q-blade software.The simulation entails establishing crucial design parameters, including design wind speed, rotor diameter, blade count, TSR, rotational speed, airfoil choice, and Reynolds number.The analysis with Q-blade assesses the conceptual design, allowing a comparative analysis of three distinct Horizontal Axis Wind Turbine (HAWT) blades in accordance with suggested criteria.Subsequently, the study identifies the most optimal design within this context.
Furthermore, this stage centred on formulating and executing an IoT framework for the hybrid PV solar-wind system.The Blynk platform, along with Arduino software, NodeMCU, relay module, temperature and humidity sensor, voltage sensor, and requisite components, were meticulously integrated.This integration was accompanied by a practical circuit diagram, complemented by meticulous coding to ensure the systematic surveillance of system data and the remote control of the system through the relay.In tandem with this effort, the hybrid PV solarwind system was constructed, the IoT architecture was meticulously devised, and the Blynk platform was adeptly configured to facilitate the wireless transmission of data via Wi-Fi.The iterative blade design process was executed through the utilization of Q-blade software-an opensource wind turbine calculation tool that expedites the design of turbine blades.This is achieved by establishing chord and twist angle distributions.The Q-blade software, rooted in the Blade Element Momentum theory, is seamlessly incorporated within an XFOIL graphical user interface.

Blade design mathematical model
The mathematical expressions used to calculate the data required for the blade design are defined by reference [33].The design wind speed has been calculated using equation ( 6) V design is the Design Wind Speed and maws is the meanannualspeed in Malaysia Where l Tip Speed Ratio: R is blade length, V is the rotational speed, and V design is the design wind speed.The Local Tip Speed Ratio (lr) is calculated using equation ( 8) where r is the local radius and R is the blade length.The Rotational Speed (V) is obtained in equation ( 9) Equation (10) in the mathematical expression for the Reynolds Number (Re) Where r is the air density m is dynamic viscosity, C is the chord length and u rel is the relative wind speed.
The Initial Angle of the Relative Wind (pi) is expressed in equation ( 11) Equation ( 12) is used to calculate the Chord Length (C r ) and Lift coefficient (Cl) Where N is the number of blades, and f is the optimum relative wind angle.The Local Twist Angle (u r ) is obtained by equation ( 13) Where: a opt is the optimal angle of attack, and b is the pitch angle.The mechanical power extracted by the WT is calculated by equation ( 14) Where Cp is the rotor power coefficient (the turbine's maximum efficiency), and V is the available wind speed.
Enhancing rotor blade performance hinges upon the judicious selection of airfoil shapes that yield heightened lift and lift-to-drag ratios.The pursuit of airfoils with a high lift-to-drag ratio proves especially advantageous for compact rotor dimensions, as they engender substantial torque generation and manifest optimal responsiveness at lower wind speeds, culminating in efficient power generation.Furthermore, the zenith of rotor blade efficacy is reached in conditions of gentle winds.Under such circumstances, the optimization of Reynolds numbers, as defined by equation ( 10), harmonizes with other parameters appraised by the BEMT.Given that low Reynolds numbers arise from the operation of diminutive rotor Wind Turbines (WTs) within the realm of low wind velocities, securing a highperformance rotor in this context necessitates airfoils boasting elevated lift and lift-to-drag ratios at low Reynolds numbers and angles of attack.To materialize this, the blade span, encompassing a radius of 0.7 m, is segmented into ten equal-length elements.Reynolds numbers of 1.5 Â 10 5 , 2.0 Â 10 5 , 2.5 Â 10 5 , and 3.0 Â 10 5 are contemplated.Airfoil data files are subsequently transposed into Q-blade software for analysis, delving into lift and drag coefficients at varying Reynolds numbers.For each chosen airfoil and Reynolds number, the pinnacle points of maximum lift and minimum drag coefficients, engendering the most favourable glide ratio, are pinpointed.The associated angles of attack that yield these optima are also discerned, as depicted in Figure 6 as an example.Referring to Table 3, it becomes evident that the SG6043 airfoil has achieved the pinnacle lift-to-drag ratio, reaching a remarkable value of 118 at a Re of 3.0 Â 10 5 and an angle of attack of 4.5 degrees.In contrast, the NACA 4412 airfoil attains its highest lift-to-drag ratio, reaching 91.3, under the conditions of a Re of 3.0 Â 10 5 and an angle of attack of 7.5 degrees.This analysis leads to the conclusion that the well-suited airfoil and Re combination are the SG6043 airfoil and a Re of 3.0 Â 10 5 , respectively.

TSR and rotational speed
One pivotal parameter in blade design influencing the initiation speed of the rotor is the TSR.With an emphasis on rapidly achieving the required torque for startup and attaining optimal power capture within a low wind speed domain, the TSR values of 4, 5, and 6 were carefully chosen for incorporation into the design.Subsequently, equation ( 9) was employed to calculate V corresponding to each designated TSR.
Referencing Table 4, the rotational speed values mark the juncture at which the rotor blade garners its peak power output, synchronized with the design wind speed and the optimal TSR setting.The parameters essential for configuring the blade design within the Q-blade software are accurately computed through the application of the design equation for TSR values of 4, 5, and 6, respectively.
The analysis reveals that the pinnacle of optimization emerges at a TSR of 6, as illustrated in Figure 7a.Additionally, Figure 7b elucidates that the optimal configuration achieved at a TSR of 6 yields the highest power coefficient in alignment with the desired outcome.

Cost analysis
To ascertain the feasibility of adopting this technology, a comprehensive cost analysis will be undertaken.This study aims to meticulously assess both the expenditures and benefits inherent to this project.The anticipated material costs for implementing this hybrid renewable energy technology are detailed in Table 5.The findings indicate that the system cost remains favourable in comparison to analogous systems documented in the existing literature.

Calibration of sensors result
To calibrate the sensors, a comparison will be made between theoretical values and actual values.The actual data was collected through an 8 h monitoring period, spanning from 9:00 AM to 5:00 PM.The theoretical data, on the other hand, were acquired by employing a multimeter and a thermometer.Subsequently, the collected data was consolidated and summarized using the mean and standard deviation formulas.The calculation process for determining the mean and standard deviation of each sensor is elucidated in the Tables 6 and 7.
By calculating the percentage difference from standard measuring instrument (m ± 1s %) between the Mean value and the Standard Deviation value, the result of the Standard Deviation value will show how far or how close the dispersion of data from mean value.It is found that m for voltage and temperature are 10.0978, and 28.944, while s for voltage and temperature are 0.0180, and 0.5003, respectively.

Hybrid system results
Based on predicted winds in Kajang, Malaysia, between 17 th February and 24 th March 2023, Figure 8a illustrates the results of theoretical computations.According to the theoretical calculations, the overall efficiency rating for both the wind turbine and gearbox/generator systems is 31.5%.In Figure 8b, the coefficient of moment is plotted against the TSR for wind velocities of 2 m/s, 3 m/s, and 4 m/s.At a wind speed of 3 m/s, the Cm graph shows the ideal pattern, in which Cm ascends to a peak and then descends.This trend, on the other hand, is not valid for wind speeds of 2 m/s and 4 m/s, as their respective graphs show fluctuating increments and decrements.
At a wind velocity of 2 m/s and a TSR of 2.4, the pinnacle of Cm stands out as the singular point where a positive value is reached, specifically at 0.0288.Remarkably, this marks the highest Cm value across all simulated scenarios.Conversely, the minimum coefficient of moment, registering at À0.0899, transpires at a TSR of 2.2, establishing the lowest value of Cm within the entire dataset.
Upon analysing the wind velocity of 4 m/s, the zenith coefficient of moment emerges at 0.0269, aligning with a TSR of 2.2.In contrast, the nadir value of Cm presents itself at À0.0282 for a TSR of 3.0.Furthermore, for wind speeds of 4 m/s, positive Cm values are observed at TSR 2.8, specifically at 0.0047.Similarly, for wind velocities at 3 m/s, positive Cm values are discernible at TSRs of 2.4 and 2.6, registering at 0.0184 and 0.0105, respectively.The lowest Cm value recorded within this wind speed category is a substantial À0.0249, occurring at a TSR of 2.2.
A theoretical wind turbine in Kajang, Malaysia generates electrical power at high wind speeds as shown in Figure 9a.According to the graph, the highest expected electrical power generation occurred on the 14 th of March 2023 at 0.88 kW, while the lowest was on the 20 th of February at 0.06 kW.There is a steady increase in electrical power generation from the 20 th to the 3 rd of March.In spite of this, the results may vary due to the cut-in wind speed of wind turbines, which is generally 4 m/s, but the forecasted wind speeds are not more than 3.06 m/s.As a result, the wind turbine will generate electricity on an hourly basis.
From the moment obtained from the CFD simulations, the power is then able to be calculated to determine the ability of the turbine.Table 8 comprises of the calculated power of the turbine for wind speeds of 2 m/s, 3 m/s and 4 m/s for TSR of 1, 2, 2.2, 2.4, 2.6, 2.8, and 3.0.From the table above the coefficients of power were also calculated to  determine the efficiency of the turbine at the specified environments.Hence, the graph for power and coefficients of power were developed below.Figure 9b displays the graph of coefficient of power against the TSR for wind speeds of 2 m/s, 3 m/s and 4 m/s.Identical to the previous graph, the graph shows and increasing trend until it reaches the peak at TSR of 2.2 and continues to consistently decrease until TSR is 3.The coefficient of power is also described as the efficiency of the turbine as it represents the ratio of power out to the power in.These coefficients must be below the Betz limit of 0.5926 which is the ideal condition of a wind turbine.In contrast to the power produced which indicated that the largest power produced by as much as 2.3779 W at 4 m/s and TSR of 2.2, the most efficient condition was obtained at wind speed of 3 m/s at TSR of 2.2 with the coefficient of power of 0.3345.The coefficient of power measured at TSR of 2.2 for both wind speeds of 2 m/s, and 4 m/s was by as much as 0.1641 and0.1588respectively.
Figure 10a shows how the wind flow creates drag on the wind turbine blades due to large areas of high velocity.The display of various speeds of wind within the area inside of the blades shows that the wind is not being fully utilised, thus strengthening the simulated results obtained from the  simulations previously.It is also evident from the long trail ends of the wind exiting the blade at a TSR of 1, which is another indication of poor performance.Changes in wind speed increase the pressure differences that enhance drag development and adversely affect the performance of wind turbines.
A comparison of Figure 10b shows there are fewer wind velocity contours within the turbine blades because they are able to better utilize the energy within the air at TSR's of 2 and 2.2.Compared to Figures 10a and b displays a larger area of higher velocity.As a result, a Darrieus wind turbine requires less lift force to operate because of the increased drag experienced by the blade.Similarly, the coefficients calculated from simulation results are in agreement with the results.

* Wind turbine rotor
Rotors were developed based on the proposed design (refer to Tab. 2).The blades were developed using 3D orienting with the material of PLA as it is most suitable for the sharp edges of the airfoil geometry.Acrylic rods were used for the shaft and connecting blade-to-shaft rods.* Solar panels and charge controllers Monocrystalline panels were used at 10W each.The solar panels were mounted at the top of the hybrid power system at an angle of 30°.Two charge controllers were used, wind turbine charge controller and solar PV charge controller, where the positive terminals of the charge controllers were connected to diodes to prevent backflow.* Inverter and battery Inverter was used to draw the DC power from the battery to AC power for he loads, which in this study uses a 20W spotlight.Battery used was a sealed lead acid battery at 12V and 18 Ah.
The percentage difference values presented in Table 9 represent the summarized results of sensor calibration, specifically focusing on the Mean and Standard Deviation (m ± 1s %).The s signifies the extent of dispersion between the data points and the m, highlighting the proximity or divergence of the data.It can be observed that the s values are smaller than their respective means, indicating minimal deviation from the mean.The average accuracy of all sensors was recorded at 98.59%, signifying their optimal performance and dependable data acquisition.Consequently, this outcome successfully fulfils the study's objective, which is the validation of the system's functionality.Figure 11a illustrate the dispersion of data, encompassing all tabulated information.
Based on Figure 11 it is evident that the data exhibits minimal dispersion.Despite occasional fluctuations in readings, the sensors demonstrate a remarkable level of accuracy.As a result, the validation of the system is confirmed.
The relay module, an integral part of the system, is also examined to validate its functionality.Testing involves activating and deactivating a light bulb to confirm the relay's capability to control the switch wirelessly.Additionally, the relay is found to be capable of activating the power source from the hybrid PV solar-wind system in case of a disruption in the main grid power supply.
The relay control functionality of the IoT system is extensively tested and validated as shown in Figure 12.It is confirmed that the relay effectively controls the on and off switching of the hybrid solar-wind system wirelessly and automatically, as intended.The relay's successful response to the NodeMCU signals verifies its functionality and contributes to the overall success of the IoT system for hybrid energy management.
Furthermore, the IoT technology employed in the hybrid system provides flexible monitoring mechanisms remotely through internet web connections.Users are able to monitor voltage, temperature, and humidity remotely and control the system on/off functionality.The system's affordability, convenience, and efficiency are highlighted.
User-friendly graphical user interfaces (GUIs) are developed using the BLYNK application for data monitoring as shown in Figure 13a.The BLYNK application allows users to choose and display the desired data, such as humidity, temperature, and voltage.A web dashboard on the BLYNK website (see Fig. 13b) is also designed for administrative and management purposes, enabling data display and system control via a computer.
The monitoring system devices showcase seamless data transmission to the cloud application and website.The system's stability is ensured through a synchronized time call interval of 1 s across all sensors.This prevents potential crashes or interruptions in the system's operation, further validating its reliability.

Comparison with similar works from literature
Reviewing several publications that focused on hybrid systems combining two PV systems and a wind turbine, it has been found that all references praised the use of these systems, which complement one another and make electricity production more reliable as illustrated in Table 10.In the researchers' study, they used a variety of wind turbines that each had advantages and disadvantages, but all needed more study to generate energy at low wind speeds of 2 m/s or less.Solar photovoltaics and hybrid wind energy systems produce far fewer emissions than fossil fuel-based electricity, according to studies.

Conclusion
In conclusion, this study presents a comprehensive approach to design and monitoring hybrid PV solar-wind systems via an IoT-based monitoring system.The proposed design seamlessly integrates sensors, microcontrollers, relay modules, and cloud servers, enabling efficient data collection, management, analysis, and remote control.The calibration process substantiates the system's reliability and precision, enabling real-time data acquisition and remote management via smartphones or computers.The incorporation of IoT technology elevates the system's functionality and user-friendliness, thereby contributing to sustainable energy practices and resource management.This design offers a robust and effective solution for monitoring renewable energy systems, ensuring accurate measurement of system parameters and optimization potential.
Based on theoretical results, the highest electrical power generation was 0.88 kW on March 14, 2023, and the lowest power generation was 0.06 kW on February 20, 2023.As a result of the increased drag that the blades are exposed to, the Darius wind turbine requires less lift to rotate.In addition, the experimental and theoretical results converged well, meaning that the assumptions were reasonable.In addition to driving the advancement of renewable energy technologies, this research paves the way for future inquiries into improving hybrid wind-solar PV system efficiency and capabilities.
While this research has contributed significantly to the design and monitoring of hybrid PV solar-wind systems through an IoT-based approach, it is essential to acknowledge certain limitations.The theoretical assumptions made during the study, while validated by the convergence of experimental and theoretical results, pose a potential constraint.Furthermore, the research primarily focuses on system monitoring and optimization, leaving room for future investigations into external factors that may impact system performance.Moving forward, future research could delve into a more comprehensive analysis of these external factors, providing a nuanced understanding of real-world challenges.

Fig. 2 .
Fig. 2. (a) Overall view of the six airfoils designed, (b) Boundary conditions of wind turbine CFD simulations.

Table 1 .
Benchmark studies in literature.F5-Efficiency Enhancement of the System: The enhancement of system efficiency is a central consideration within this component, encompassing strategies and methodologies applied to bolster overall performance.

Table 2 .
Geometry of the wind turbine rotor.

Table 4 .
Rotational speed of varying TSR.

Table 5 .
The estimated cost of materials in the system.

Table 8 .
Moment and coefficient of power at different TSR and wind speed.

Table 9 .
Data calibration of each sensor.

Table 10 .
Comparison between the recent study and others from literature.configuration for 231 kWh/day is a 16.1 kW photovoltaic system, a 5.1 kW wind turbine, a 16.3 kW inverter, and 220 kWh of storage.A solar panel system produces 22,276 kWh of electricity per year.A total of 70,446 kWh/year are generated by the wind turbine F.B.I.Alnaimi et al.: Renew.Energy Environ.Sustain.9, 2 (2024)

Table 10 .
(continued).renewableenergy sources was used in this study to maintain voltage management and voltage stability of the entire microgrid system through the use of power electronics.These power quality problems can be fixed or at least reduced by the proposed hybrid system.In this microgrid, solar and wind power generation can fluctuate irregularly, and the energy storage system can serve as a backup power source.Darrieus wind turbine An energy generation system that combines solar and wind power was developed in this study.A number of improvements were suggested to the blade shape using the Q-blade program in the study.According to the results of the study, a maximum of 0.88 kilowatts of electricity can be generated.The increased drag that is exposed to the blades of Darius wind turbines also reduces the required lift to operate them.F.B.I.Alnaimi et al.: Renew.Energy Environ.Sustain.9, 2 (2024)